Bathroom Light

[Size: 2 Lights]
Looks exactly like it should

[Size: 2 Lights]
Very attractive light as pictured.

[Size: 2 Lights]
The build quality of the light is good. The cones are lightweight, but solid and hold their shape under gentle pressure. The base feels heavy and solid. The gold cone interiors are cool, and what make the light distinctive. If you like this light based on the product photos, I would say go for it for sure.The finish is where this light falls a bit short for me personally. It's advertised as oil rubbed bronze, but the painted surface is very uniform and lacks the depth, variation, and character I typically associate with oil rubbed bronze. For this reason, I think it will compliment other oil rubbed bronze fixtures by being in a similar color family, but it doesn't quite fit as a true match. The description clearly states that it's painted, and the product photos are accurate. I was simply hoping it would have more character to it in person.

[Size: 2 Lights]
This is a beautiful, too-light vanity with black mat coloring and a gold interior shade. Please see the attached video for a closer look at some installation instructions for this vanity.This would be a beautiful and very appropriate vanity for a small bathroom or children’s bathroom. You could also use it if you was in entranceway or living room for additional light I place it in the bathroom and I get two lightbulbs and I would make certain that they were Edison lights if possible that’s why the glasses is clear and you can see the filaments even though their LED filaments they would be I get the attractive most attractive ones that I could and I keep the wattage down to probably a maximum of 12 to 16 W. That’s a lot of LED power even for a bathroom we want light for Makeup and shaving and things like that manufacturer says they’ll handle up to 60 W of incandescent bulbs but I would recommend that you get either 12 to 16 W bulbs the max because remember every 9 W of LED power is the equivalent to 100 W lightbulb of incandescent pipe.Installation is easy, but as with all installations, I always recommend that you make absolutely certain you’ve turned off the power at the circuit control panel box in your home. Circuit brake control panel box. Your home is normally located in the basement. And in some homes, the circuit breaker control panel boxes are located in the garage, particularly if you do not have a basement.Once you locate the circuit brake control panel box since I’m going to assume you’re removing an existing picture that you’re displaced with and putting in this fixture as a replacement have someone stand in the room with the light on in the bathroom and a cell phone line open to you as you turn off the circuit practice into turn off the one that affects that light then I turned it on off several times just to make sure that we had the right circuit. To make further certain after you turn it off, make further certainty that you have turned it off. I would take an electrical testing device, a voltage meter, and test every wire in that junction box before disconnecting the old lighting fixture to make certain the power is off.If you look at the attached video, you’ll see that there’s an install plate attached to the base of the picture in the mounting fixture area, and it’s connected with two decorative black screws. Move the black screws. Remove the install plate. Thread the house service wires through the sensor hole of the installed plate. Make certain the last half centimeter of insulation has been removed from the tips of the wires, and then place the black wire adjacent to the black wire from the fixture. Remove the insulation from the wire fixture as well, and please install a wire lock nut over both wires and tighten it clockwise. A firm mechanical and electrical connection has been established.Do the same thing with the white wire and the green wire, which, in this case, connects to a bare copper wire coming from the fixture.Once you’ve secured the install plate with two number-eight machine screws into the junction box, gently place all the wiring and lock nuts into the junction box. Make certain another kind apart as you do this. Next, take the canopy you removed the install plate from, return it, and replace the two block screws you removed to tighten it securely to the install plate.Take the rings as I describe them to you and show them to her in the video. Remove the shade holding rings place the shades over the E 26 outlets, replace the shade holding rings, and then install the E 26 lightbulbs that you purchased into the fixtureAt this point, go turn on the circuit breaker at the control panel box, turn on the switch in the bathroom, and test your work to make sure everything’s working correctly. This is a beautiful value light that will give you years of pleasure.